If you have tried changing the light colors on the projector, it’s likely that the app settings are different, causing the light issue.įor this reason, we recommend that you select the desired color from the app and save the settings. The light projectors are connected to the speaker with the VGA cable, and a damaged cable can cause issues in the accuracy of the light.įor this reason, you must inspect the VGA cable and replace it if there is fraying or bends. If you have selected a specific color on the light projector, but it illuminates a different color, it means that there is discoloration. Unfortunately, replacing the LEDs can be challenging, which is why we recommend replacing the entire unit. If these two solutions don’t work, it indicates that the LEDs in the projector are short (it can be caused by voltage or power fluctuation). If it’s really hot, you have to let it rest for a few minutes. On the other hand, if rebooting or taking the projector out of the standby mode doesn’t help, you should touch the unit to check for overheating. To resolve this issue, you’ve to turn off the projector and turn it on later. However, if the lights are turning on but keep blinking, it’s likely that the unit is in standby mode. The light projector is designed to offer even and well-lit illumination on the walls. For this reason, it’s recommended that you put the projector on a shelf or side table. Lastly, you shouldn’t put the projector in a tight or cornered area because it can restrict the airflow and cause overheating. If they are blocked, you can use a toothbrush to clean them. Secondly, you have to check all the vents and buttons on the projector and inspect them to make sure the dirt isn’t blocking them. The first step is to clean the area around your light projector because dirt and dust buildup is the most common reason behind overheating. However, they can also overheat when the unit needs air circulation, cleaning, or maintenance. Since light projectors are designed to impart light and illumination, it’s common for them to get overheated. Once it’s turned off, press the power button again to turn it on. So, we recommend that you access the light projector, look for the power button, and press it to turn it off. The galaxy night light projector has been designed with the standby mode, with which the projector stops projecting light when you turn it on but don’t turn on the lights. So, take out the batteries and install them correctly. On the other hand, if you have recently changed the batteries, it’s likely that you haven’t installed the batteries correctly. If you haven’t changed the batteries in months, you have to purchase new batteries for the remote control and install them properly (you can consult the manual to determine which are the correct batteries). In case you are using the remote control to turn on and use the light projector, it’s likely that the remote control’s batteries are low and don’t have power anymore. Once the projector comes back to its normal temperature, turn it on. If it’s too hot to touch, you have to let it rest so the temperature is normalized. The overheated unit will turn off for safety purposes.įor this reason, we recommend that you take out the cable and charger and touch the projector. If the power outlet is operational, but the light projector is still not turning on, it’s likely that the unit is overheated. On The other hand, if you don’t have another outlet available to plug in the charger, you should get the outlet repaired by an electrician. The quickest solution is to change the outlet rather than get the outlet fixed. However, if the light projector is not turning on, you have to consider the following solutions.įirst of all, you have to check the power outlet because the projector’s charger must be plugged into a reliable and working power outlet. The light project depends on the battery to turn on, but you can plug in the charger and use the projector directly – it can be recharged for portable use or when it’s plugged into the power source. So, if you have purchased the light projector, it’s important to be aware of the common Star Galaxy Night Light Projector problems troubleshooting guide – it helps fix the common errors quickly! It can be connected to voice assistants for control, or you can use a remote control to control the music selection, lighting, timer, volume, and rotation.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |